濟南批膩子總起泡？原因找對不用愁，本地實用解決方案

　　Is Jinan putty always foaming? Don't worry about finding the right reason, local practical solutions

　　在濟南的家庭裝修或墻面翻新中，批膩子起泡是師傅們最頭疼的常見問題之一。剛批好的墻面冒出密密麻麻的小氣泡，不僅影響施工進度，業主也會忍不住擔心是不是濟南膩子粉的質量出了問題，經銷商更是要反復解釋溝通。其實膩子起泡大多不是材料本身的問題，而是施工環境、墻面基層或操作方法沒把控好。今天就專門科普濟南地區批膩子起泡的原因和實用解決辦法，幫大家避開這個施工坑。

　　In home decoration or wall renovation in Jinan, foaming with putty is one of the most common headaches for craftsmen. The newly approved wall is covered with dense small bubbles, which not only affects the construction progress, but also makes the owner worry about whether the quality of Jinan putty powder is the problem. The dealer has to explain and communicate repeatedly. In fact, the foaming of putty is mostly not a problem with the material itself, but rather a result of poor control over the construction environment, wall substrate, or operating methods. Today, we will specifically explain the reasons and practical solutions for the foaming of putty in Jinan area, to help everyone avoid this construction pit.

　　先說說最常見的起泡原因，首當其沖的是墻面基層問題。濟南很多老房子是混凝土澆筑的墻體和天花板，基層表面本身就比較粗糙，布滿了細小孔洞。批膩子時，這些孔洞里的空氣會被膩子層壓縮，等后續空氣反彈就會頂起膩子，形成一個個小氣泡。另外，新批的砂漿墻面如果沒度過養護期，水泥里的堿性成分沒完全揮發，遇到膩子中的水分就會產生氣體，也容易引發起泡。

　　Firstly, let's talk about the most common causes of bubbling, with the first and foremost being issues with the wall substrate. Many old houses in Jinan have concrete poured walls and ceilings, and the surface of the base layer itself is relatively rough, covered with small holes. When applying putty, the air in these holes will be compressed by the putty layer, and when the air rebounds later, it will lift up the putty and form small bubbles. In addition, if the new batch of mortar walls has not passed the curing period and the alkaline components in the cement have not completely evaporated, they will produce gas when encountering the moisture in the putty, which can also easily cause foaming.

　　還有兩個容易被忽視的原因，都和濟南的氣候特點有關。濟南春季多風干燥，墻面吸水過快；夏季高溫高濕，墻面又可能吸水過慢，這兩種情況都會導致膩子層水分蒸發不均，進而產生氣泡。除此之外，施工操作不當也會踩坑：比如膩子粉攪拌得太稀，水分過多會讓干燥過程中氣體更易排出；或者批刮得太厚，空氣難以滲透揮發，也會形成氣泡。

　　There are two other reasons that are easily overlooked, both of which are related to the climate characteristics of Jinan. Jinan is windy and dry in spring, and the walls absorb water too quickly; High temperature and humidity in summer, coupled with slow water absorption on walls, can lead to uneven evaporation of moisture in the putty layer, resulting in the formation of bubbles. In addition, improper construction operations can also cause pitfalls: for example, mixing putty powder too thinly and too much moisture can make it easier for gases to be released during the drying process; Or if the scraping is too thick, the air is difficult to penetrate and evaporate, which can also form bubbles.

　　不少業主看到起泡就慌了，其實不用過分擔心，針對性處理就能解決。如果已經出現氣泡，等膩子快干的時候，讓師傅再收一次刀把氣泡壓破；或者在刮第二遍膩子前，把氣泡鏟破處理干凈，一般刮第二、三遍膩子后就不會再出現氣泡了，既不影響施工質量，也不會破壞完工后的美觀，只是需要師傅多費點功夫。

　　Many homeowners panic when they see bubbles, but there is no need to worry too much. Targeted treatment can solve the problem. If bubbles have already appeared, when the putty is about to dry, ask the master to use the knife again to crush the bubbles; Alternatively, before applying the second coat of putty, the air bubbles can be cleared and cleaned. Generally, after applying the second or third coat of putty, there will be no more air bubbles, which will not affect the construction quality or damage the appearance of the finished product. It just requires the master to put in more effort.

　　這里要特別說一句，越是質量好的濟南膩子粉，出現氣泡的情況可能反而更明顯。因為優質膩子粉的膠粉含量高、粉料細膩，密閉性更好，空氣不容易滲透出來，尤其是在濟南炎熱的夏季，這種情況會更突出。想要從源頭減少氣泡，不妨試試這四個本地施工常用的辦法：

　　It should be noted that the better the quality of Jinan putty powder, the more obvious the occurrence of bubbles may be. Because high-quality putty powder has a high content of adhesive powder, fine powder, better sealing, and less air infiltration, especially in the hot summer of Jinan, this situation becomes more prominent. To reduce bubbles from the source, try these four commonly used local construction methods:

　　第一，提前涂刷墻固。墻固能固化墻面基層，填補細小孔洞，減少空氣殘留，這是濟南施工中預防起泡的基礎步驟。第二，攪拌膩子時加點料。可以適量加一點水泥或粉刷石膏，能改善膩子的透氣性，讓空氣更容易排出。第三，堅持薄批原則。批刮時越薄越好，分多次完成，這樣空氣能充分揮發，避免堆積在膩子層內。第四，保證攪拌均勻。膩子粉和水要充分攪拌，不能有結塊，同時控制好加水量，別太稀也別太干。

　　Firstly, apply wall reinforcement in advance. Wall solidification can solidify the base layer of the wall, fill small holes, and reduce air residue, which is the basic step to prevent foaming in construction in Jinan. Secondly, add some material when mixing putty. Adding a small amount of cement or plaster can improve the breathability of the putty and make it easier for air to escape. Thirdly, adhere to the principle of thin batches. When scraping, the thinner the better, and it should be done in multiple times so that the air can fully evaporate and avoid accumulating in the putty layer. Fourth, ensure even mixing. The putty powder and water should be thoroughly mixed without clumping, and the amount of water added should be controlled, neither too thin nor too dry.

　　其實批膩子起泡不是什么大難題，關鍵是找對原因、用對方法。對于濟南的業主來說，了解本地氣候對施工的影響，選擇適配的優質膩子粉，再配合規范的施工操作，就能有效避免氣泡問題。希望這次科普能幫大家打消顧慮，在墻面裝修時少走彎路，做出平整美觀的墻面。

　　Actually, foaming putty is not a big problem, the key is to find the right cause and use the right method. For homeowners in Jinan, understanding the impact of local climate on construction, choosing suitable high-quality putty powder, and cooperating with standardized construction operations can effectively avoid bubble problems. I hope this science popularization can help everyone dispel their concerns, avoid detours when decorating walls, and create smooth and beautiful walls.

　　本文由   濟南膩子粉   友情奉獻.更多有關的知識請點擊  http://www.netjobs.cc/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Jinan Putty Powder For more related knowledge, please click http://www.netjobs.cc/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.